- 您现在的位置：买卖IC网 > Sheet目录303 > 844USB (B&K Precision)DEVICE PROGRAMMER USB INTERFACE
Specification of ISP connector pins depends on the device, which you want to program. You
can find it in the control SW for programmer (PG4UW), menu Device / Device Info (Ctrl+F1) .
Be aware, the ISP programming way of respective device must be selected. It is indicated by
(ISP) suffix after name of selected device.
These specifications correspond with application notes published of device manufacturers.
Used application notes you may find on www.bkprecision.com , section Support /
Application Notes.
Note: Pin no. 1 is signed by triangle scratch on ISP cable connectors .
As ISP connectors are used 20 pins connectors 09185207813 from Harting or other
compatible connector.
866C ISP cable
Warnings:
? When you use 866C as ISP programmer , don’t insert device to ZIF socket .
? When you program devices in ZIF socket , don’t insert ISP cable to ISP connector .
? Use only attached ISP cable . When you use other ISP cable (other material, length…),
programming may occur unreliable.
? 866C can supply programmed device (pin 1 of ISP connector) and target system (pins 19
and 20 of ISP connector) with limitation (see Technical specification / ISP connector).
? 866C apply programming voltage to target device and checks his value (target system
can modify programming voltage). If the programming voltage is different as expected, no
action with target device will be executed.
Multiprogramming by 866C
During installation of PG4UW at Select Additional Tasks window you check, if is allowed
install 866C multiprogramming control support.
For start of 866C multiprogramming is necessary run special control program pg4uwmc.exe .
At this program user assign 866C to control programs, may load projects for all 866C and run
PG4UW for every connected and assigned 866C.
Selftest and calibration check
If you feel that your programmer does not react according to your expectation, please run the
programmer (ISP connector) selftest using Diagnostic POD (Diagnostic POD for ISP
connectors #2), enclosed with the standard delivery package.
20
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
84702-0008
CONN RECEPT ETHERNET 8-8 PNL MNT
848A
MEMORY PROGRAMMER PARALLEL INTER
85506-0001
CONN MOD JACK VERT 8-8 HI-SPEED
85507-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-5001
CONN MOD JACK 8POS T/H HI SPEED
85511-0001
CONN MOD JACK VERT 8-8 HI-SPEED
862015-1
6 POS RECEPTACLE
相关代理商/技术参数
845
功能描述:程序设计器 - 基于通用和内存 REORD 615-865 UNIV. WITH SOFTWARE
RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC
845 1 1/2"X15YD
功能描述:SCOTCH BOOK TAPE 845 1-1/2 IN X 制造商:3m 系列:* 零件状态:在售 标准包装:24
845 3"X15YD
功能描述:SCOTCH BOOK TAPE 845 3 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:12
845 4"X15YD
功能描述:SCOTCH BOOK TAPE 845 4 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:8
845 PRO4
制造商:Micro-Star International 功能描述:845 P4 S478 SDRAM LAN - Bulk
845 PRO4-L
制造商:Micro-Star International 功能描述:845 P4 SKT478 ATX SDRAM - Bulk
845 ULTRA
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk
845 ULTRA-DF
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk